Crimestopper Alarms
Bookmark and Share

 

!

Crimestopper FS-80 Touch Screen 2 Way Paging Car Alarm and Remote Start
!
crimestopper fs-80

General Features

  • 2-Way FM/FM Combo Alarm, Keyless Entry and Remote Start System
  • 2-Way FM/FM Touch Screen Paging Remote with Fully Animated LCD Graphics and Audible Tones for Confirmation of Alarm Status, Violation and Engine Start
  • Includes Sidekick Non-Paging Remote
  • Dynamic Code Protection (Anti Code-Grabbing)
  • Code Learning Receiver
  • Electronic Dual-Stage Shock Protection (Plug-In Design)
  • Multi-Zone Trigger Protection
  • Defective Zone Bypass with Warning Chirps
  • Alarm Pre-Warning Signal
  • Manual Arming Mode: Allows you to arm/disarm the system without carrying a remote control
  • On-Board Relay for Flashing Lights
  • Audible and Visual Arm/Disarm with Intrusion Alert
  • Programmable Carjack Protection
  • Programmable Vehicle Horn Output
  • Remote Panic Protection
  • 25W High-Power Mini Single Tone Siren
  • Passive Door Locks (Programmable)
  • Passive & Active Re-Arming Mode (Programmable)
  • LED Diagnostic for Last Zone Triggered
  • Remote Keyless Entry
  • Built-In Door Lock Relays
  • Dual Parking Light Relays (+) or (-)
  • Auto Lock/Unlock Through Vehicle's Ignition
  • Separate Driver's Door Unlock Priority
  • Double Unlock Pulse (Programmable Feature for Factory Interface)
  • 1 or 3 Second Door Lock Pulse (Programmable)
  • Silent Arm/Disarm Through the Remote
  • (6) Programmable Remote Auxiliary Outputs: Momentary, Timed or Latched
  • (4) Vehicle Operation
  • Dome Light Illumination
  • Programmable Arm/Disarm Chirps
  • Transferable Limited Lifetime Warranty
  • 86 Programmable Options

Remote Start Features

  • Turbo Timer Mode: Allows Engine to Continue Running from 1-5 Minutes After Key Removal
  • "Ultra Smart" Tachless Mode
  • Programmable "Wake Up" Ignition Pulse on Unlock for Vehicles with "Slam Locks"
  • Timed Crank Mode (Pre-set Starter Cranking time in 4 Increments of 0.5-1.5 Seconds)
  • Glow Plug Input or Programmable Timed Delay for Diesel Engines
  • (5) On-Board Remote Start Relays for Easy Installation: ACC, IGN, IGN2, Start, and Parking Lights
  • Selectable Engine Speed Sensing: "Smart" Tachless or Tach (RPM) Learning
  • Remote Start Diagnostics
  • 3rd Start Output
  • Tach Finder Mode
  • Timed Start Mode
  • Idle Down Mode
  • Programmable Engine Run Time: 3min, 10min, 15min or 20min
  • Factory OEM Alarm Arm/Disarm Outputs
  • Negative Ignition Output for Additional Relays or Anti-Theft Bypass Modules
  • Hood Open Safety Circuit: Unit will not Remote Start if Hood is Open or Ajar
  • Foot Brake or Parking Brake Option

Remote Features

  • 2-Way FM/FM Touch Screen Pager with Fully Animated, Color 3D LCD Graphics and Voice Confirmation of Alarm Status, Violation, and Remote Engine Starting
  • Rechargeable Internal battery
  • Range Meter
  • Vehicle Battery Voltage Check Meter
  • Vehicle Temperature Check Meter
  • Parking Meter Timer
  • Alarm Clock
  • Daily Timed Start
  • Trigger Record (Check the Time and Date of the Last 4 Alarm Triggers or Violations)
  • Pin Code Set: Remote will not unlock the doors unless the proper code has been entered into the remote (Programmable)
  • Alarm Status Check
  • Real Time LCD Clock
  • Backlight Adjustment: Bright, Dark, Etc
  • English or Spanish Language Settings
  • Silent Arm/Disarm
  • Arm Without Shock Sensor
  • Car Finder Mode
  • Button Lock Protection: Buttons can be Locked to Prevent Accidental Pressing
  • Power Save Mode

Crimestopper SP-500 2 Way Paging Car Alarm and Remote Start
!
crimestopper sp-500

General Features

  • 2-Way FM/FM Combo Alarm, Keyless Entry and Remote Start System
  • 2-Way FM/FM Paging Remote with LCD Graphics for Confirmation of Alarm Status, Violation and Engine Start
  • Enhanced White and Red LED Backlit Screen
  • Includes Sidekick Non-Paging Remote
  • 2-Way Data Port allows for Direct Plug-In Data Modules For Easier Installation
  • 433 MHz High Frequency with Extended Range On-Glass Antenna
  • Dynamic Code Protection (Anti Code-Grabbing)
  • Code Learning Receiver
  • Audible and Visual Arm/Disarm with Intrusion Alert
  • Silent Arm/Disarm Through the Remote
  • Remote Panic Protection
  • Programmable Arm/Disarm Chirps
  • Passive & Active Arming Mode (Programmable)
  • Active Rearm Mode (Programmable)
  • Carjack Protection (Programmable)
  • Electronic Dual-Stage / Dual Adjustment Shock Sensor
  • Alarm Pre-Warning Signal
  • Defective Zone Bypass with Warning Chirps
  • LED Diagnostic for Last Zone Triggered
  • Programmable Vehicle Horn-Honk Output
  • 25W High-Power Mini Single Tone Siren
  • On-Board Relay for Flashing Lights
  • Dome Light Illumination
  • (4) Remote Auxiliary Outputs: 2 Fixed, 2 Programmable (Timed, Momentary or Latched On/Off)
  • Remote Keyless Entry
  • Negative Door Lock Outputs
  • Separate Driver's Door Priority Unlock
  • Passive Door Locks (Programmable)
  • Double Unlock Pulse (Programmable)
  • Auto Lock/Unlock Through Vehicle Ignition (Programmable)
  • 1 or 3 Second Door Lock Pulse (Programmable)
  • (2) Vehicle Operation
  • Transferable Limited Lifetime Warranty
  • 31 Programmable Options

Remote Start Features

  • Turbo Timer Mode: Allows Engine to Continue Running from 1-5 Minutes After Key Removal (Requires Additional Switch)
  • Selectable Engine Speed Sensing: "Smart" Tachless or Tach (RPM) Learning
  • "Ultra Smart" Tachless Mode with Custom 80-100% Voltage Range Adjustment  Tach Finder Mode
  • Timed Crank Mode (Pre-set Starter Cranking time in 4 Increments of 0.5-1.5 Seconds)
  • Glow Plug Input or Programmable Timed Delay for Diesel Engines
  • Programmable "Wake Up" Ignition Pulse on Unlock for Vehicles with "Slam Locks"
  • Programmable Engine Run Time: 12, 24, 36 or 48 Minutes
  • (5) On-Board Remote Start Relays for Easy Installation: ACC, IGN, IGN2, Start, and Parking Lights
  • Factory Alarm Arm/Disarm Outputs
  • Negative Ignition Output for Additional Relays or Anti-Theft Bypass Modules
  • Hood Open Safety Circuit: Unit will not Remote Start if Hood is Open or Ajar
  • Foot Brake Reset Input
  • 3rd Start Output
  • Remote Start Diagnostics Through Parking Lights

Crimestopper SP-400 Car Alarm and Remote Start
!
crimestopper sp-400

General Features

  • 1- Way Combo Alarm, Keyless Entry, and Remote Start System
  • (2) 4-ButtonTransmitters with Sliding Button Guard to Prevent Accidental Button Press
  • 2-Way Data Port allows for Direct Plug-In Data Modules For Easier Installation
  • 433 MHz High Frequency with Extended Range On-Glass Antenna
  • Dynamic Code Protection (Anti Code-Grabbing)
  • Code Learning Receiver
  • Audible and Visual Arm/Disarm with Intrusion Alert
  • Silent Arm/Disarm Through the Remote
  • Remote Panic Protection
  • Programmable Arm/Disarm Chirps
  • Passive & Active Arming Mode (Programmable)
  • Active Rearm Mode (Programmable)
  • Carjack Protection (Programmable)
  • Electronic Dual-Stage / Dual Adjustment Shock Sensor
  • Alarm Pre-Warning Signal
  • Defective Zone Bypass with Warning Chirps
  • LED Diagnostic for Last Zone Triggered
  • Programmable Vehicle Horn-Honk Output
  • 25W High-Power Mini Single Tone Siren
  • On-Board Relay for Flashing Lights
  • Dome Light Illumination
  • (4) Remote Auxiliary Outputs: 2 Fixed, 2 Programmable (Timed, Momentary or Latched On/Off)
  • Remote Keyless Entry
  • Negative Door Lock Outputs
  • Separate Driver's Door Priority Unlock
  • Passive Door Locks (Programmable)
  • Double Unlock Pulse (Programmable)
  • Auto Lock/Unlock Through Vehicle Ignition (Programmable)
  • 1 or 3 Second Door Lock Pulse (Programmable)
  • (2) Vehicle Operation
  • Transferable Limited Lifetime Warranty
  • 31 Programmable Options

Remote Start Features

  • Turbo Timer Mode: Allows Engine to Continue Running from 1-5 Minutes After Key Removal (Requires Additional Switch)
  • Selectable Engine Speed Sensing: "Smart" Tachless or Tach (RPM) Learning
  • "Ultra Smart" Tachless Mode with Custom 80-100% Voltage Range Adjustment  Tach Finder Mode
  • Timed Crank Mode (Pre-set Starter Cranking time in 4 Increments of 0.5-1.5 Seconds)
  • Glow Plug Input or Programmable Timed Delay for Diesel Engines
  • Programmable "Wake Up" Ignition Pulse on Unlock for Vehicles with "Slam Locks"
  • Programmable Engine Run Time: 12, 24, 36 or 48 Minutes
  • (5) On-Board Remote Start Relays for Easy Installation: ACC, IGN, IGN2, Start, and Parking Lights
  • Factory Alarm Arm/Disarm Outputs
  • Negative Ignition Output for Additional Relays or Anti-Theft Bypass Modules
  • Hood Open Safety Circuit: Unit will not Remote Start if Hood is Open or Ajar
  • Foot Brake Reset Input
  • 3rd Start Output
  • Remote Start Diagnostics Through Parking Lights

Crimestopper SP-300 2 Way Paging Car Alarm
!
crimestopper sp-300

General Features

  • 2-Way FM/FM Paging Alarm/Keyless Entry System
  • 2-Way FM/FM Pager Remote with Enhanced Range
  • Enhanced White & Red LED Backlighting
  • Screen Turns Red When for Trigger Alerts
  • LCD Graphics and Real Time Page Back for Confirmation of Alarm Status
  • Built-In Clock on Pager Remote
  • Pager Remote Uses Standard AAA Battery
  • Dynamic Code Protection (Anti Code-Grabbing)
  • Code Learning Receiver
  • Audible and Visual Arm/Disarm with Intrusion Alert
  • Silent Arm/Disarm Through the Remote
  • Remote Panic Protection
  • Programmable Arm/Disarm Chirps
  • Passive & Active Arming Mode (Programmable)
  • Active Rearm Mode (Programmable)
  • Carjack Protection (Programmable)
  • Plug-In Electronic Dual-Stage / Dual Adjustment Shock Sensor
  • Alarm Pre-Warning Signal
  • Programmable Vehicle Horn-Honk Output
  • On-Board Relay for Flashing Lights
  • Dome Light Illumination
  • Programmable Vehicle Horn-Honk Output
  • Single Tone 125db Electronic Siren Remote Keyless Entry
  • Negative Door Lock Outputs
  • Passive Door Locks (Programmable)
  • Double Unlock Pulse (Programmable)
  • Auto Lock/Unlock Through Vehicle Ignition (Programmable)
  • 1 or 3 Second Door Lock Pulse (Programmable)
  • (2) Vehicle Operation
  • Transferable Limited Lifetime Warranty
  • 15 Programmable Options

Crimestopper SP-100 Car Alarm
!
crimestopper sp-100

General Features

  • 1- Way Alarm/Keyless Entry System
  • 2 Ultra-Slim Style Remote Transmitters
  • Code Learning Receiver
  • Audible and Visual Arm and Disarm with Intrusion Alert
  • Electronic Dual-Stage Shock Sensor (Plug-In Design)
  • Alarm Pre-Warning Signal
  • On-Board Relay for Flashing Lights
  • Separate Right / Left Parking Light Outputs for European Based Vehicles
  • Carjack Protection (Programmable)
  • Programmable Vehicle Horn-Honk Output
  • Single Tone 125db Siren
  • Remote Panic Protection
  • Remote Keyless Entry
  • Silent Arm/Disarm Through the Remote
  • Auto Lock/Unlock Through Vehicle Ignition (Programmable)
  • Passive Door Locks (Programmable)
  • Double Unlock Pulse (Programmable)
  • 1 or 3 Second Door Lock Pulse (Programmable)
  • (1) Remote Auxiliary Output
  • Programmable Arm/Disarm Chirps
  • Transferable Limited Lifetime Warranty
  • 12 Programmable Options

Crimestopper SV-6350-OEM Rear View Camera OEM Design for Toyota Camry / Corolla
!
crimestopper sv-6350-oem

As part of Crimestoppers's OEM camera line, the SecurView™ OEM-6350 is designed specifically to fit in the factory camera mounting location on the Toyota Camry and Corolla vehicles for the 2009 to present models. Once the camera is installed, you can't tell whether it is factory or aftermarket and is easily kept out of sight. The ultra-wide 170° viewing angle will give the driver the best view behind the vehicle as well as the new Distance Guard grid which will help judge the distance between the vehicle's rear bumper to an object.


The OEM-6350 is designed to be custom mounted onto the vehicle. For this installation you can see the camera is halfway submerged into the rear license plate bezel panel. This kind of mounting makes it look completely factory installed and gives it a low profile on the vehilce.

  • Ultra-wide 170° viewing angle
  • Image device: 1/4 inch color CMOS sensor
  • Specifically designed for the Toyota Camry and Corolla Vehicles
  • Camera looks completely factory installed and is easily kept out of sight
  • Distance guard feature to help judge distance when backing up your vehicle
  • NTSC full color
  • 1 LUX sensitivity for enhanced illumination in low-light conditions
  • Reverse image built-in
  • Can be hooked up to any standard monitor
  • Waterproof design (IP68)

Crimestopper SV-5110 Rear View PlateCam Bar Type CMOS Color Camera
!
crimestopper sv-5110

The SecurView™ SV-5110 is a bar type camera designed to be mounted on the vehicle license plate using the existing license plate holes. It has an ultra-wide 180° viewing angle to give the driver the absolute best view behind the vehicle. There is no drilling or cutting required making it very easy to install taking very little time. This uniquely design camera can be used on any passenger car, truck, SUV or van. It can even be used on bigger trucks, buses or motor homes. The waterproof design allows the camera to face harsh weather elements in any climate.

  • Bar-Mount Design allows for quicker and easier installation without having to drill oversize holes.
  • 115° Horizontal Viewing Angle.
  • 2 Lux Sensitivity for Enhanced illumination in Low Light Conditions.
  • Reverse Mirror Imaging Built-In.
  • Waterproof Camera Design.
  • Lens: f = 2.8mm.
  • Current consumption: 60 mA.

Crimestopper CA-5011 Reverse Parking Sensors with LED Display
!
crimestopper ca-5011

The Backstopper™ CA-5011 is a rear impact warning sensor system designed to aid the driver when backing up their vehicle. The system includes a color LED digital display with a four-sensor direction indicator mode and (4) ultra-sonic sensors with "quick disconnect" waterproof connectors.

The colorful LED digital display has a built-in buzzer for visual and audible warning. The display also has a four-sensor direction indicator which allows the driver to see which sensor is being set of the most. This is useful to allow you do know exactly where the obstruction is behind the vehicle. The design is a top-dash mount design which makes the display easy to mount in several locations such as the top of the dash board, inside a pocket or on top of the rear view mirror.

The sensors wide detection angle will alert the driver of any small children, pedestrians, animals or small unseen objects such as bicycles or parking poles. This makes it very convenient for parking in a parking garage, a crowded lot or even in your own driveway.

The CA-5011 system has a top-dash mounted LED display with a 4-direction sensor indicator to give the driver separate distance readings on every sensor. It can be mounted on top of the dash board, the steering column or even on top of the rear-view mirror like shown in the picture.

The sensors can be painted to match the color of the vehicle. This way the vehicle can still look clean and not appear as though any aftermarket equipment has been installed. A hole saw bit comes included with the system to help drill the exact size hole needed to fit the sensors into place.

  • Top Dash mounted LED Display Panel with 4-Stage Audible Obstruction Warning
  • (4) Insert Type Ultra-Sonic Sensors with "Quick Disconnect" Connectors
  • Sensors can be Painted to Match the Color of the Vehicle
  • Built-In Warning Beeper
  • Extended Sensor Cables to Run Under Truck Beds
  • Audible Warning: 3 Distinct Beep Tones Notify You of the Distance to an Object
  • Simple Wiring Installation
  • Includes Hole saw for Drilling the Sensor
  • Waterproof Sensors
  • You Can Feel Safe When Putting Your Car in Reverse
  • Easier Parking, Especially for Parallel Parking Situations
  • State-of-the-Art Design
  • Compact Design Using the Latest Ultra-Sound Technology
  • Prevents Accidental Impacts
  • Alerts You to Small Animals, People, or Unseen Objects
  • Extra Wide Detecting Angles to Prevent Side Impacts (Convenient for Parking Garages)
  • Preventing Accidents can Save you Money Due to High Insurance Premiums and Repair Costs

Crimestopper CA-5016 Front & Back Detection System Audible & Visual Warning
!
crimestopper ca-5016

The Backstopper™ CA-5016 is a front and rear impact warning sensor system designed to aid the driver not only when backing up the vehicle but also when pulling forward. The system includes a colorful LED digital display with a four sensor direction indicator as well as an external plug-in style audible buzzer. (8) ultra-sonic sensors are also included with the system for front and back signaling as well as an on/off switch for the front sensors.

The crystal-clear colorful LED digital display comes with a four-sensor direction indicator which will also indicate when it is the front or the rear sensors detecting the obstruction. The external plug-in style buzzer will alert the driver to an obstruction with a three-stage audible warning and different alert tones for the front and back sensors

An on/off switch is included with the system for the front sensors to turn them on and off when needed. The system also has a foot-brake input that can be wired with the on/off switch. This means that when the front sensors are turned on, the driver will get a distance reading when the foot brake is applied making it very convenient when parking in a garage or cramped parking lot.

The sensors wide detection angle will alert the driver of any small children, pedestrians, animals or small unseen objects such as bicycles or parking poles in the front or the rear of the vehicle.

  • Front and rear impact warning
  • Crystal-clear colorful LED digital display (20ft. cable length)
  • Four-sensor direction indicator mode for front and rear sensors
  • Flexible bracket for easy installation of display
  • External plug-in style buzzer for audible warning
  • Three-stage audible obstruction warning signaling
  • Different alert tones for front and rear sensors
  • (8) ultra-sonic sensors with "quick disconnect" waterproof connectors (25ft. length)
  • On/off switch included for front sensors
  • Foot brake input for front sensor activation
  • Sensors can be painted to match the color of the vehicle
  • Hole saw bit included for sensor installation

Crimestopper SV-5200IR Top Mount License Plate Camera with IR
!
crimestopper sv-5200ir

The SecurView™ SV-5200.IR is a bar type camera designed to be mounted on the vehicle license plate using the existing license plate holes. It has a 180° viewing angle to give the driver the absolute best view behind the vehicle as well as Infra-Red LED for night vision to provide the best lighting in night time driving conditions. There is no drilling or cutting required making it very easy to install taking very little time. This uniquely designed camera can be used on any passenger car, truck, SUV or van. It can even be used on bigger trucks, buses or motor homes. The waterproof design allows the camera to face harsh weather elements in any climate.

The SV-5200.IR mounts easily to the license plate using the existing factory license plate screws. The rounding shape gives it a cleaner look on the vehicle and the plate-mount design makes it easy to install requiring no holes to be drilled and no modifying of the license plate.

  • Ultra-wide 180° viewing angle
  • Black or Chrome finish
  • Image device: 1/4 inch color CMOS sensor
  • Bar mount design allows for quicker and easier installation without drilling any holes
  • Infra-red LED for night vision
  • NTSC full color
  • 1 LUX sensitivity for enhanced illumination in low-light conditions / 0 LUX with night vision
  • Normal or reverse image (Selectable)
  • Easy to fit over most license plates
  • Can be hooked up to any standard monitor
  • Waterproof design (IP68)
  • Available in Chrome or Black Color

Crimestopper SV-5420IR Full Plate License Plate Camera with IR
!
crimestopper sv-5420ir

The PlateCam™ SV-5420.IR is a special designed full-frame license plate mounted reverse camera with an ultra-wide 180° viewing angle to give the driver the absolute best view behind the vehicle. This camera also comes equipped with multiple LEDs for night vision to make it easier to see in night time driving conditions. The camera lens and LEDs can be swiveled vertically to give a better viewing angle depending on where the license plate is on the vehicle, whether it is up high or down low. The license plate frame design makes it very easy to install on the vehicle without requiring any holes to be drilled for mounting and also gives it a low-profile look on the vehicle.

The SV-5420.IR can be used on any passenger car, truck, SUV or van. It can even be used on bigger trucks, buses or motor homes. The waterproof design allows the camera to face harsh weather elements in any climate.

The SV-5420.IR is a full license plate frame with a CMOS camera integrated into the top bar of the frame. The mounting style is the same as the SV-5400.IR. No drilling is required for installation and the license plate does not need to be modified.

  • Ultra-wide 180° viewing angle
  • Black or Chrome finish
  • Image device: 1/4 inch color CMOS sensor
  • Camera is fully integrated into a custom license plate frame
  • Camera lens and IR LEDs can be rotated for better viewing angle.
  • NTSC full color
  • 1 LUX sensitivity for enhanced illumination in low-light conditions
  • Normal or reverse image (Selectable)
  • Easily mounts to any license plate
  • Can be hooked up to any standard monitor
  • Waterproof design (IP68)

Crimestopper SV-8600.TS 3.5" Universal Mount Touch Screen LCD Monitor
!
crimestopper sv-8600.ts

The SecurView™ SV-8600.TS is a touch screen video monitor with a 3.5" high-definition digital display. Besides the full touch screen display, the monitor has a wide variety of features such as a built-in speaker for audio playback, multiple language selection, normal and reverse image switching and all full sound/picture adjustments.

The monitor also includes an adjustable universal mount bracket to allow itself to be mounted anywhere on the dashboard or windshield depending on the owner's preference.

The SV-8600.TS can be used with any of the SecurView™ or PlateCam™ cameras or any other camera that uses an RCA cable video connection. There are two video inputs to support two different cameras or one camera and an external DVD player. The primary video input has auto-switching control for the reverse camera.

  • 3.5" high definition digital LCD monitor
  • Full touch screen display
  • Includes adjustable bracket for dashboard or windshield mounting
  • Low-profile design
  • Built-in speaker for audio playback
  • Multiple language selection (English, Spanish, French, German, Dutch, Italian, Portuguese & Russian)
  • Anti-glare protection
  • 2 video inputs: Auto switching for reverse camera
  • Normal or reverse image switching
  • Pixels: 480(H) x 234(V)

Crimestopper SV-9155 Replacement Style Rear View Mirror with 4.5" Monitor
!
crimestopper sv-9155

The SecurView™ SV-9155 is a replacement style rear view mirror monitor for driver's that want a video camera system with the factory look. This style of mirror completely replaces the OEM mirror while giving you the convenience of a 4.5" LCD monitor. Once the mirror is installed it looks completely factory and the screen is completely invisible when not in use.
 
The mirror not only has the screen but also comes with (2) sets of video and audio inputs for a reverse camera and an external DVD player, or for two reverse cameras. The primary video input has auto switching capability when the reverse camera activates. A distance guard display can be activated on the reverse camera's input to help the driver judge distance when backing up. The built-in speaker will provide audio playback for cameras with a built-in microphone.
 
The SV-9155 can be used with any of the SecurView™ or PlateCam™ cameras or any other camera that uses an RCA cable video connection.

The SV-9155 is a replacement style rear view mirror that completely takes the place of your existing factory rear view mirror when installed. It has a built-in 4.5" LCD screen which turns completely invisible when it is not in use and will automatically turn on when the vehicle is shifted into reverse.

WARNING: Some OEM rear view mirrors may have built-in electronic components such as OnStar™, Compass and Thermometers or dome lamps. Removal of the factory mirror may result in non-operation of these components. Make sure to check with your installer before removing the factory mirror.

  • Replacement style rear view mirror monitor
  • Mirror completely replaces the OEM mirror
  • Built-in 4.5" LCD screen
  • Screen is invisible when not in use
  • Distance guard feature to help judge distance when backing up your vehicle
  • Built-in speaker for audio playback
  • Anti-glare protection
  • (2) audio / video Inputs: Auto switching for reverse camera
  • Normal or reverse image switching