Soundstream Human Reign Amplifiers
Bookmark and Share

 

!

Soundstream HRU.2 Human Reign 2 Channel Amplifier
!
sound stream hru.2

Human Reign amplifiers accept low level and balanced line inputs via a BLT Balanced Line Transmitters and the long-biased transistor period yield unparalleled sound quality. With a pre-amp section that is unrivaled by any other brand, the Human Reign amplifiers are the ultimate audiophile products for the ultimate audiophile system...

  • Pure Class A circuitry 2 Channel Amplifier
  • 2 X 450 Watts @ 4 Ohm
  • 2 X 900 Watts @ 2 Ohm
  • 1 x 1800 Watts @ 4 Ohm Bridged
  • THD: <0.20%
  • S/N Ratio: >90dB
  • Damping Factor: >500
  • Frequency Response: 20Hz - 20KHz
  • Input Sensitivity: 0.15 - 5 Volt
  • Crossover LPF 24dB: 40Hz - 160Hz
  • Channel 1&2 HPF 12dB: 50Hz - 500Hz
  • Hawkins in Subsonic: 13Hz - 30Hz
  • Hawkins in Position: 30Hz - 70Hz
  • Variable Bass Boost: 0 - 90dB
  • Fully regulated MOSFET power supply
  • RUBI™ (Rapid-Use Branched Impulse) Proprietary power supply topology
  • STACT™ (STabilized Apex Current Topology) Reduces power supply stress by 50%
  • Auto High Current™ Matches the amplifier for virtually every load application
  • Chassi-sink™ Semiconductors are situated between the circuit board and heat sink for optimal thermal transfer
  • Ultra-Low ESR Capacitance Bank ensures rapid power delivery for dynamic peaks
  • Triple Darlington output circuitry
  • Hawkins Bass Control™ Proprietary bass equalization topology
  • Harmonic Bass Alignment™ Produces tighter and more accurate bass
  • IDI™ (Intelligent Distress Indicator) Gives visual indication of amplifier protection status
  • Bi-Linear built-in selectable 2-way crossovers for amplifier and line output
  • 4-Way protection topology - Thermal, DC Offset, Speaker Short and Reverse Polarity
  • Selectable Balanced line inputs for highest level of noise rejection
  • Optional BLT-4

Soundstream HRU.4 Human Reign 4 Channel Amplifier
!
sound stream hru.4
Human Reign amplifiers are back! The original series were very pricey due to the extraordinary heatsink. The guts are the same high end parts you loved in the original, but now at about half the price!
  • Pure Class A circuitry 4 Channel Amplifier
  • 4 X 125 Watts @ 4 Ohm
  • 4 X 250 Watts @ 2 Ohm
  • 2 x 500 Watts @ 4 Ohm Bridged
  • THD: <0.20%
  • S/N Ratio: >90dB
  • Damping Factor: >500
  • Frequency Response: 20Hz - 20KHz
  • Input Sensitivity: 0.15 - 5 Volt
  • Crossover LPF 24dB: 40Hz - 160Hz
  • Channel 1&2 HPF 12dB: 50Hz - 500Hz
  • Channel 3&4 HPF 12dB: 50Hz - 500Hz
  • Hawkins in Subsonic: 13Hz - 30Hz
  • Hawkins in Position: 30Hz - 70Hz
  • Variable Bass Boost: 0 - 90dB
  • Fully regulated MOSFET power supply
  • RUBI™ (Rapid-Use Branched Impulse) Proprietary power supply topology
  • STACT™ (STabilized Apex Current Topology) Reduces power supply stress by 50%
  • Auto High Current™ Matches the amplifier for virtually every load application
  • Chassi-sink™ Semiconductors are situated between the circuit board and heat sink for optimal thermal transfer
  • Ultra-Low ESR Capacitance Bank ensures rapid power delivery for dynamic peaks
  • Triple Darlington output circuitry
  • Hawkins Bass Control™ Proprietary bass equalization topology
  • Harmonic Bass Alignment™ Produces tighter and more accurate bass
  • IDI™ (Intelligent Distress Indicator) Gives visual indication of amplifier protection status
  • Bi-Linear built-in selectable 2-way crossovers for amplifier and line output
  • 4-Way protection topology - Thermal, DC Offset, Speaker Short and Reverse Polarity
  • Selectable Balanced line inputs for highest level of noise rejection
  • Optional BLT-4